Batwing: Yes

Mower Type: Pull-Type

Width: 144

RC2512 Series 2 Only needs 40HP PTO to operate. Get your mowing done faster!!
This is a common stock item for us usually keeping at least one on the yard at all times. Perfect mower for clipping pastures or cutting brush and everything in between. Low Rate financing options and delivery available! Please call with any questions

Specifications & Capacities
Tractor horsepower 40-100 hp (29.8-74.6 kw)
Gearbox horsepower Splitter
Center & wings
160 hp (119.3 kw)
100 hp (74.6 kw)
Gearbox shafts Input shaft
Output shaft
1 3/8" (3.5 cm) 6 Spline
1 1/2" (3.8 cm)
Gearbox capacity & lubrication
Splitter
Center & wings
4.5 pints (2.13 L) of gear lube 80-90W EP
4 pints (1.89 L) of gear lube 80-90W EP
Cutting capacity 1 1/2" (3.8 cm)
Hitch weight 793 lbs (359.7 kg)
Machine weight 2,540 lbs (1152.1 kg)
Blade tip speed At 540 rpm Center Blades = 16,500 FPM (83.8 mps) Wing Blades = 16,000 FPM (81.3 mps)
Hitch types LP Performance hitch and swivel hitch
Hitch jack Standard (2,000 lbs) (907.2 kg)
Cutting width
Overall cutter width
Minimum transport width
12'-0" (3.66 m)
12'-7" (3.84 m)
7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground.
Overall length 13'-3" (4.04 m)
Deck height 11" (27.9 cm)
Cutting height 1 1/2" to 12" (3.8 cm to 30.5 cm)
Lift hydraulics 2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings & stroke control spacers
Wing folding hydraulics 2" bore x 8" stroke hydraulic cylinders, hoses & fittings
Wing flex 22o Down and 45o up while cutting.
Wing transport protection Wing transport locks
Deck material 10 Gauge (3.4 mm) deck
Side skirt material 3/16" (5 mm) Plate
Skid shoes Wing deck: 1 replaceable per wing
Center deck: 2 replaceable shoes
Blade rotation Left wing
Center deck
Right wing
Counterclockwise
Counterclockwise
Clockwise
Blades - 6 (2 per deck) 1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift
Blade overlap 6" (15.2 cm)
Blade bolt Keyed with hardened flat washer & locknut
Stump jumper / blade holder 10 Gauge (3.4 mm) round dish shaped pan, reinforced
with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar
Front & rear guards Single chain
Input driveline Category 4 with constant velocity u-joint
Intermediate & wing drivelines Category 3 with slip-clutch
Wheels 20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires
or 21" (53.3 cm) laminated wheels
Number of wheels 4 - Wheels: 2 on transport axle and one on each wing axle
Transport axle Spring-cushioned lift cylinder
Signal lights
7 Pin connector
LED
SAE J560 pin configuration
Hubs Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.